Crash-Rated Barriers & M30/M50 Bollards
How crash-rated barriers are rated, what each type is for, and what a project must decide before pricing.Anti-ram bollards, wedge barriers, crash beams, crash-rated gates and cable systems stop a vehicle at a defined speed and weight. This page explains how they are rated, what each type is for, and what a project must decide before pricing.
Get a quote
Step 1 of 2
Takes about a minute. Nothing is sent until you press “Get my quote”.
Start typing — pick a suggestion or keep what you typed.
Crash ratings explained (ASTM F2656)
ASTM F2656/F2656M is the standard test method for crash testing vehicle security barriers. A barrier is rated by crashing a defined test vehicle into it at a defined speed and measuring how far the vehicle gets past it.
ASTM F2656 also rates passenger car (C), small pickup (SD), pickup (PU) and heavy goods vehicle (H) tests; M (15,000 lb medium-duty truck) is the most commonly specified. M ratings are written M30, M40 and M50 for a nominal impact speed of 30, 40 or 50 mph.
| ASTM F2656 rating | Test vehicle | Nominal impact speed | Legacy DOS equivalent |
|---|---|---|---|
| M30 | Medium-duty truck, 15,000 lb (6,800 kg) | 30 mph (48 km/h) | K4 = M30-P1 |
| M40 | Medium-duty truck, 15,000 lb (6,800 kg) | 40 mph (64 km/h) | K8 = M40-P1 |
| M50 | Medium-duty truck, 15,000 lb (6,800 kg) | 50 mph (80 km/h) | K12 = M50-P1 |
K-ratings correspond only to P1 (≤1 m penetration). An M-rating with P2–P4 is not equivalent to a K-rating. A rating belongs to the manufacturer’s tested barrier system, including its foundation, as shown in the certified test report. It is not a property of the installer.
Penetration ratings (P1–P4)
The penetration rating records how far the front of the truck’s cargo bed travelled past the barrier during the test. Penetration is measured from the inside (non-impact) face of the barrier. A full rating combines both parts, for example M50-P1: the barrier stopped a 15,000 lb truck at 50 mph with the cargo bed travelling no more than 1 m (3.3 ft) past the inside face.
| Penetration rating | Dynamic penetration distance |
|---|---|
| P1 | ≤1 m (3.3 ft) |
| P2 | 1.01–7 m (3.31–23.0 ft) |
| P3 | 7.01–30 m (23.1–98.4 ft) |
| P4 | >30 m (>98.4 ft) |
Penetration is measured from the inside (non-impact) face of the barrier.
Legacy K-ratings (DOS SD-STD-02.01)
Older specifications use the U.S. Department of State K-ratings from SD-STD-02.01. K4, K8 and K12 used the same 15,000 lb truck at 30, 40 and 50 mph with a penetration limit of 1 m, so K4 = M30-P1, K8 = M40-P1 and K12 = M50-P1.
K-ratings correspond only to P1 (≤1 m penetration). An M-rating with P2–P4 is not equivalent to a K-rating.
ASTM F2656 replaced the K-rating test method; when a document still lists a K-rating, the P1 equivalent above is normally accepted, subject to the design team’s confirmation.
Barrier types and what each is for
Each type is rated as a complete system. The right choice depends on the rating required, how often vehicles must pass, and what is underground.
- Fixed bollards: permanent standoff at building fronts, entries, plazas and equipment, where vehicles never need to pass.
- Removable bollards: lift out with a key or tool for occasional service or emergency access.
- Retractable bollards: lower automatically or manually so authorized vehicles can pass, then rise again; they need power, drainage and controls.
- Wedge barriers: a steel plate that rises at a vehicle entry; common at checkpoints with frequent traffic.
- Crash beams: a rated swing or drop arm across a lane, used where an entry must open fully.
- Crash-rated gates: sliding, cantilever or swing gates tested as a complete system with their posts and footings.
- Crash-rated fence and cable systems: fence lines reinforced with tensioned cables or beams, anchored at engineered end points, to stop vehicles along a long perimeter.
What the specifier must provide or decide
A crash rating reflects a single test at a specified impact point. It does not guarantee the same performance under every site condition, approach route or foundation — which is why the manufacturer’s foundation design and site layout matter.
A crash-rated scope cannot be priced or substituted responsibly without these decisions in the documents.
- Required rating: vehicle, speed and penetration (for example M30-P1 or M50-P1), based on the site’s threat and vulnerability assessment.
- Approach speed and site layout: the longest straight run a vehicle can build speed on, and the barrier line that protects the required standoff.
- Engineered foundations: footing design per the manufacturer’s tested details and the engineer of record, including soil and reinforcement.
- Underground utility conflicts: utilities, drainage and slabs along the barrier line; shallow-foundation products exist where deep footings conflict.
- Submittals and certified test reports: the manufacturer’s certified test report for the exact model and rating, shop drawings and installation instructions.
- Power, drainage and controls for active barriers (retractable bollards, wedge barriers, crash beams and gates), coordinated with the electrical and access-control scope.
How Las Vegas Fence participates
Our role depends on the barrier type:
- Crash-rated fixed bollards: We price specified crash-rated fixed bollards to the project documents.
- Crash-rated removable / retractable bollards: We price specified crash-rated removable and retractable bollards to the project documents.
- Wedge barriers / crash beams: We price specified wedge barriers and crash beams to the project documents.
- Crash-rated gates: We price specified crash-rated gates to the project documents.
- Crash-rated fence / cable barrier systems: We price specified crash-rated fence and cable barrier systems to the project documents.
Standards referenced
Rating definitions on this page follow these published standards:
- ASTM F2656/F2656M — Standard Test Method for Crash Testing of Vehicle Security Barriers
- ASTM F2781 — Standard Practice for Testing Forced Entry, Ballistic and Low Impact Resistance of Fence Systems
- ASTM F3016/F3016M — Standard Test Method for Surrogate Testing of Vehicle Impact Protective Devices at Low Speeds
- U.S. Department of State SD-STD-02.01, Revision A — Test Method for Vehicle Crash Testing of Perimeter Barriers and Gates (superseded by ASTM F2656)
FAQ
Common questions
Is a standard steel pipe bollard crash-rated?
No. A concrete-filled pipe bollard can stop low-speed impacts, but a crash rating applies only to a manufacturer’s system tested to ASTM F2656 and installed with its tested foundation, spacing and reinforcement.
Can a crash-rated product be substituted?
Only with the design team’s approval. The substitute needs a certified test report for the same or a higher rating, and its foundation must suit the site.
What does M50-P1 mean?
The barrier stopped a 15,000 lb (6,800 kg) medium-duty truck at a nominal 50 mph, and the front of the cargo bed travelled no more than 1 m (3.3 ft), measured from the inside (non-impact) face of the barrier.
Related
Related services, industries & projects
Ready to start?
Get a quote for your site.
Tell us what you need and where. We will follow up to scope the work.